Moving Van Bodies
- Standard body lengths
10'-28' (inside)
Features:
|
photo of Moving Van Bodies coming
soon! |
Front
·
Aerodynamic front design, 12"
radius with heavy duty corner castings, 5" front post radius
utilizing 1/8" rugged aluminum extrusion |
Roof Bows
·
Roll-formed 18 guage galvanized steel,
anti-snag configuration, located on 24" centers |
Roof
·
One-piece aluminum, tension-fitted and
bonded to roof bows, perimeter riveted. Roof assembly bolted to top
rail structure for easy removal and repair |
Crossmembers
·
3" hi tensile "C"
channel on 12" centers, fully welded at each end to steel
mounting rail, alternating crossmembers gusseted to longitudinals,
full crossmembers over wheels |
Rear Frame
·
11 gauge galvaneal steel with
reinforcement at all stress points |
Floor
·
1 1/8" laminated hardwood. All
floors coated with polyurethane varnish |
Longitudinals
·
Structural steel "C" channel |
Exterior Lights
·
Marker lights recessed in roof cove
with exterior wiring in protective groove. All connectors shielded
from moisture by heat-shrink insulators |
Interior Light
·
Roof-mounted dome light, recessed
switch in wall inside rear door opening |
Mounting
·
Body mounted on customer supplied
chassis. Hardwood filler strips are steel banded to top of chassis
frame rails. Zinc plated u-bolts are placed through crush pipes to
hold body in place tighter, longer, and to prevent over-tightening and
bending of frame rails. |
Undercoating
·
Petrol base on full understructure |
Posts
·
Double slotted logistic posts on
16" or 24" centers, side and front posts extend 6 3/8"
below floor |
Walls
·
Aluminum panels, pre-painted white,
baked enamel |
Peak
·
Strong unique "Z"-mounting
rail construction with welded cross-members, 3/4" plywood floor
with FRP exterior panel on bottom side |
Mounting Rail
·
Heavy-duty steel "Z" shaped
mounting rail runs full length of body on each side and across front |
Lining
·
1/4" plywood on sides and on front
wall |
·
Reflectors
Installed as required to comply with FMVSS |
Bumper & Rear Door Options
·
48" Pull Out Tailgate with
ICC Bumper
·
Bumper Step
·
Two-Panel Swing Doors Full
Opening
·
ICC Bumper
·
12" Split Dock Bumper with
Two Steps
·
ICC Bumper with Floor Extension
6" & 12" |
|
[ top
of page ] |
|
Refrigerated Van Bodies
- Body Lengths: 10' to 28'
Features: |
photo of Refrigerated Van Bodies
coming soon! |
Front
·
Heavy 7 guage reinforced steel frame
supports and model refrigeration unit, aluminum corner castings,
5" radius front nose and corners, heavy-duty .040" aluminum
sheet, fiberglass pultruded posts, 4" foamed in-place non-CFC
polyurethane insulation |
Side Walls
·
Heavy-duty .040" aluminum sheet,
fiberglass pultruded Z posts on 16" centers, additional posts at
high stress areas, 3" or 4" poured polyurethane insulation |
Crossmembers
·
3" hi-tensile "C"
channel steel on 12" centers, alternating crossmembers gusseted
to longitudinals |
Roof
·
Thick .032" one-peice aluminum
sheet, pultruded Z posts on 24" centers, 3" or 4"
polyurethane insulation |
Rear Frame
·
Heavy-duty stainless steel, 12 guage
posts and header, 7 guage sill |
Rear Door
·
DuraPlate swing doors, 3" poured
insulation, Kemlite glassboard interior, aluminum hinges with
stainless steel pins on swing doors |
Liner
·
.090" seamless
Kemlite glassboard on all interior sides, front and ceiling |
Electrical
·
All wiring enclosed in conduit for easy
access, plus heat shrink wire connections at all ends help seal out
moisture |
Undercoating
·
Petrol based coating used on full
understructure |
Reefer Unit
·
Customer choice of brands |
Interior Lighting
·
Rapid cold-start fluorescent dome
light, recessed in a sealed, insulated enclosure |
Scuff Plate
·
12" high extruded aluminum |
Floor
·
Extruded aluminum hat, front and rear
smooth gutters with drains, flush rear entry for forklift loading
3" or 4" poured polyurethane insulation, composite stringers |
Side Door
·
DurePlate exterior skin, poured foam
filled, Kemlite glassboard interior lined, internal reinforcement at
header and sill, aluminum hinges with stainless steel pins, stainless
steel grab handle. |
Exterior
Lighting
·
Marker lights recessed in roof cove
with exterior wiring in protective groove |
|
[ top
of page ] |
StepSide Van Bodies
- Available in 3 side door
configurations:
Sliding, Swing, & Roll-up
Features:
|
Photo of StepSide Van Bodies
coming soon! |
·
Available in aluminum or FRP construction; van lengths from 10' to 30'
·
Extra strong front and side walls, with body
posts extending
·
6 3/8" below the floor for maximum strength
·
Recessed aluminum and skid resistant stepwell entry
·
Top quality aluminum construction Sliding door, durable and light weight, 1/8" thick, .50 inch overlay
·
Full 36" X 80" opening for sliding door
·
Standard 32" X 80" swing-type and roll-up doors
·
Quality door latch/handle/lock assembly
Custom rear doors and bumpers |
|
[ top
of page ] |
|
